The iFloor 3 can work for up to 25 minutes under normal mode.

Normally this does not happen because the brush roller diameter size is big enough so it can avoid getting tangled. If there is a tangle, just remove the brush roller from its holder and use the cleaning tool to remove the hair tangle from the brush roller.

There is no need to use distilled water. Tap water is perfectly fine to use in the iFloor series. Please do not use hot water as this can cause internal damage to the pipes in the iFloor series.

We would not recommend using bleach in this machine as it could damage the machine.

The product weighs about 10 lbs.

The warranty lasts 2 years.

The unique brush roll can help to remove animal hair and suck it into the Dirty Water Tank.

No, the cleaning solution does not have an odor, but it can deodorize the area you are cleaning.

The max button enables higher speed and stronger spray to help remove tough spots and stains.

The Tineco iFloor series uses 100-240V in its charger. We do not recommend using a different charger as that may not be compatible with the battery.

The Clean Water Tank capacity is 0.6L. The Dirty Water Tank capacity is 0.5L.

Using the cap of the solution bottle, fill one cap worth of solution and pour into the Clean Water Tank. Fill up the Clean Water Tank with clean water up to the Max line.

The temperature can be between 41°F ~ 140°F （5°C ~ 60°C). Typically normal tap water is fine to use for cleaning. Please do not use hot water as this can cause internal damage to the pipes in the Floor One.

We recommend storing the iFloor 3 on the storage tray that is provided with the iFloor 3. The storage tray allows the self-cleaning function to work more easily as the tray was designed to fit the head of the iFloor 3.

The iFloor 3 will automatically adjust the solution and clean water flow to make sure you have the ideal cleaning experience. You can adjust the water flow to maximum by entering MAX mode when cleaning. This will set the flow to maximum for when you have a tough cleaning situation.

The flow rate is either 50ml/min or 220ml/min in relation to normal mode and max mode.

iFloor 3 is updated version of hard floor washer based on the iFloor model. It has about 3.7 times more suction power and 100% higher brush roller power compared to the iFloor so it can achieve better cleaning results.

There is no need to vacuum an area first because the Ifloor 3 can vacuum and wash the floor simultaneously.

The Ifloor series can be used on non-carpeted floor such as vinyl, tile, and sealed wood floors.

The Ifloor / IFLOOR 3 can be used without water for dry vacuuming. Ideally you would want to use the Ifloor 3 with solution and water to automatically adjust solution and clean water flow to ensure an ideal cleaning result.

It is not recommended to use a third party cleaning solution because the floor washer is designed to be used with the Tineco Cleaning Solution to optimize the amount of bubbles that are produced with cleaning solutions. Third party solutions can cause an over abundance of bubbles when cleaning that could fill up the Dirty Water Tank within minutes of use.

The floor washer produces up to 78dBA of sound.

To start the iFloor 3's self-cleaning mode, please follow the following steps: Always keep the floor washer plugged in. Place the floor washer on the storage tray. Empty the Dirty Water Tank. The Clean Water Tank should be at least 1/3 full of water. Press self-cleaning button at the top of the handle to start the brush roll self-cleaning mode. The floor washer will automatically shut off once finished. The entire self-cleaning process takes about 40 seconds.

We recommend cleaning the brushroll after each use.

Suction power for the floor washer ranges from 15-30AW (Air Watts) depending on how dirty the floor is.

The iFloor 3 has a Lithium-ion 21.6V 3000mAh battery that allows it to run 25 minutes depending on how often the floor washer is running on max power.

The iFloor 3 takes around 4 hours to charge to full.